Johnson-controls AFFINITY 340968-XIM-A-0108 User Manual download pdf (Page 13)

340968-XIM-A-0108

Johnson Controls Unitary Products 13

SEQUENCE OF OPERATION

The unit is controlled by a conventional heating/cooling ther-

mostat common to this class of equipment.

HEATING

The control board begins a call for heat when W1 is ener-

gized (connected to R). The control ignores W2 until pilot

ignition has been established.

The control checks to see if the pressure switch is open. If the

pressure switch is closed, the control board flashes "3" on the

LED and waits indefinitely for it to open. When the pressure

switch is sensed as open, the control begins pressure switch

proving period. If the call for heat is lost, the control goes

back to Standby.

PRESSURE SWITCH PROVING

The control board energizes the induced draft motor (High

speed for 2 stage model) and waits for the low pressure

switch to close. When the low pressure switch closes, the

control begins Pre-purge period. If the call for heat is lost, the

control de-energizes the inducer without post-purge and

returns to standby.

If the low pressure switch does not close within 10 seconds of

inducer energizing, the control board flashes "2" on the LED.

If the pressure switch does not close within 5 minutes of

inducer energizing, the control shuts off the inducer for 30

seconds, then energizes the inducer for another 5 minute try

to close the pressure switch. This cycle continues indefinitely

until either the pressure switch is proved closed, or the call

for heat ends.

PRE-PURGE

The control board monitors the low pressure switch and

ensures it remains closed during pre-purge. If the pressure

switch opens, the control goes back to pressure switch prov-

ing mode. The control waits for a 15 second pre-purge

period, then begins the ignition trial

IGNITION TRIAL PERIOD

The control board energizes the pilot gas valve and spark

outputs for an 85 second Ignition trial. The control de-ener-

gizes the spark when flame is sensed and enters a flame sta-

bilization period.

If flame is not established within the ignition trial period, the

control de-energizes the spark and gas valve and begins an

inter-purge period before attempting another ignition trial.

If the call for heat is lost during an ignition trial period, the

control immediately de-energizes spark and gas. The control

runs the inducer motor through a post purge period before

de-energizing.

If the pressure switch is lost during an ignition trial period, the

control immediately de-energizes spark and gas. The control

begins pressure switch proving before an inter-purge and re-

ignition attempt.

PILOT FLAME STABILIZATION PERIOD

The control board de-energizes the spark output, and waits

for a 2 second flame stabilization period before energizing the

main gas valve.

If flame is lost during the flame stabilization period, the con-

trol board counts it as a flame loss and retries ignition or locks

out flashing a "5" on the LED.

HEAT BLOWER ON DELAY

The control board waits for 30 seconds and then energizes

the indoor blower heat speed. Blower on delay time begins at

the start of flame proving period in the trial for ignition.

If the thermostat demand for heat is removed, the control de-

energizes the gas valve, energizes the blower on heat speed

and initiates a post-purge and heat blower off delay.

MAIN BURNER OPERATION

High heat warm-up

Two stage models run high heat for the first 60 seconds fol-

lowing Pilot Flame Stabilization period regardless of W2

demand. If W2 is not energized at the end of this 60 second

period the control de energizes the high gas output and steps

the inducer to low speed. If W2 is energized the control

remains on high heat.

There is no high heat warm-up on single stage models

Low heat

The control board keeps the pilot gas valve, main gas valve

and induced draft motor energized while continuously moni-

toring the call for heat, low pressure switch, and flame status.

If the call for heat (W1) is lost, the control de-energizes the

gas valve and begins post purge.

If low pressure switch opens, the control de-energizes the

gas valve and begins pressure switch proving mode.

If flame is lost, the control de-energizes the gas valve within

2.0 second and counts the flame loss. If flame has been lost

more than 16 times within the same call for heat, the control

board locks out flashing "5" on the LED. If flame has been

lost less than 16 times, the control attempts re-ignition after a

300 second inter-purge period.

High heat

If the W2 terminal was energized more than 1 second before

W1 at the start of the call for heat, and remains continuously

energized through the call for heat, the control considers it to

be connected to a single stage thermostat and implements a

10 minute Auto staging feature. The 2nd stage thermostat

call is ignored until 10 minutes into steady heat (9 minutes

after high heat warm-up ended).

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 23 24

Comments to this Manuals

No comments

Johnson-controls AFFINITY 340968-XIM-A-0108 User Manual Page 13

Comments to this Manuals

Related products and manuals for Conditioners Johnson-controls AFFINITY 340968-XIM-A-0108